Welcome to the State Water Resources Control Board Welcome to the California Environmental Protection Agency
Governor's Website Visit the Water Board Members Page
Agendas
My Water Quality
Performance Report
UST Program - LG 113

UST Programs - LG 113

Issue Date: November 22, 1995
Revision Date: October 18, 2002
 

OPW Fuel Management Systems
(originally listed as Petro Vend, Inc.)

Site Sentinel Models II and III, 
(Model 613, 4 inch dia Floats, Magnetostrictive Probe)

AUTOMATIC TANK GAUGING METHOD

Certification Leak rate of 0.2 gph with PD = 99.82% and PFA = 0.18%. 
Leak rate of 0.1 gph with PD = 99.95% and PFA = 0.35%.
Leak Threshold 0.1 gph for leak rate of 0.2 gph. 
0.06 gph for leak rate of 0.1 gph. 
A tank system should not be declared tight if the test result indicates a loss that equals or exceeds this threshold.
Applicability Gasoline, diesel, aviation fuel. 
Other liquids with known coefficients of expansion and density may be tested after consultation with the manufacturer.
Tank Capacity Maximum of 15,000 gallons. 
Tank must be between 50 and 95% full for leak rate of 0.2 gph. 
Tank must be minimum 90% full for leak rate of 0.1 gph.
Waiting Time Minimum of 12 hours between delivery and testing. 
There must be no delivery during waiting time. 
Minimum of 30 minutes between dispensing and testing.
Test Period Minimum of 2 hours for leak rate of 0.2 gph. 
Minimum of 4 hours for leak rate of 0.1 gph. 
Test data are acquired and recorded by system's computer. 
Leak rate is calculated as the difference between the first and last data collected. 
There must be no dispensing or delivery during test.
Temperature Average for product is determined by a minimum of 5 resistance temperature detectors (RTDs).
Water Sensor Must be used to detect water ingress. 
Minimum detectable water level in the tank is 0.92 inch. 
Minimum detectable change in water level is 0.02 inch.
Calibration RTDs and probe must be checked and, if necessary, calibrated in accordance with manufacturer's instructions.
Comments

Not evaluated using manifolded tank systems. Therefore, this certification is only applicable when there is a probe used in each tank and the siphon is broken during testing.  
Tests only portion of tank containing product. 
As product level is lowered, leak rate in a leaking tank decreases (due to lower head pressure). 
Consistent testing at low levels could allow a leak to remain undetected. 
EPA leak detection regulations require testing of the portion of the tank system which routinely contains product.

California regulations require at least one test per month after routine product delivery or when the tank is filled to within 10% of the highest operating level of previous month. If the 0.1 gph test is used as a tank tightness test there must be no water present in the backfill (groundwater must be below the bottom of the tank), the tank must be equipped with an overfill protection device, and the product level in the tank must be at the overfill protection device set point. Local agency pre-approval is required. To use the 0.1 gph test as a monthly option see title 23 CCR Section 2643 (b)(2).

OPW Fuel Management Systems

Evaluator:  Underwriters Laboratories, Inc.

6900 Santa Fe Dr.

Tel:  (847) 272-8800

Hodgkins, IL 60525-9909

Date of Evaluation:  11/04/94

Tel:  (708) 485-4200

 | Home | Vendors: A - F | Vendors: G - M | Vendors: N - S | Vendors: T - Z | Method Index |

Appearance on this list is not to be construed as an endorsement by any regulatory agency nor is it any guarantee of the performance of the method or equipment.
Equipment should be installed and operated in accordance with all applicable laws and regulations.
For full details, please refer to our expanded "DISCLAIMER" page.

 
 

.