Welcome to the State Water Resources Control Board Welcome to the California Environmental Protection Agency
Governor's Website Visit the Water Board Members Page
My Water Quality
Performance Report
UST Program - LG 113

UST Program - LG 113

Issue Date: November 17, 2005
Revision Date: February 3, 2011

 Franklin Fueling Systems

Secondary Containment Monitoring (SCM)


Certification Certified as equivalent to European leak detection standard EN 13160-2, Part 2, as a Class I leak detection system.
Operating Principle System uses vacuum generated by the turbine pump to continuously maintain a partial vacuum within the interstitial space of double-walled tanks and double-walled piping.
System is designed to activate a visual and acoustic alarm, and optional turbine pump shutdown before stored product can escape to the environment.
System is capable of detecting breaches in both the inner and outer walls of double-walled tanks and double-walled piping.
Alarm Condition System alarms when a liquid or air leak occurs which causes the interstitial vacuum to decrease (pressure to increase) and the system is unable to maintain minimum vacuum.
System will also alarm if the interstitial vacuum level decreases at a rate exceeding manufacturer's allowable values. Allowable values are based on an "AutoLearn line leak algorithm." The unit will record two curves (up curve and down curve) while a calibrated leak orifice is connected to the interstitial space being monitored. The "up" curve is learned while the vacuum pump is on and evacuating the interstice. The "down" curve is learned when the vacuum pump is off and interstitial vacuum is decaying. During normal operation when the vacuum level is between the upper and lower limits, the system is continuously comparing vacuum decay rates to the learned curves stored in memory.
Applicability Underground double-walled tank, connected double-walled piping, and other connected interstitial spaces storing gasoline, gasohol, diesel, heating oil #2, kerosene, aviation fuel, motor oil, water.
EN13160-2 requires the use of separate monitoring systems for separate USTs.

*This evaluation determined the sensor's responses to the liquids shown above. Biodiesel blends B6-B20 meeting ASTM D7467 and biodiesel B100 meeting ASTM D6751 would also produce an alarm if the sensor threshold is exceeded. Responses to these fuels were not determined, but would be expected to be very similar to the diesel responses.
Manufacturer's Specifications Alarm will activate when interstitial vacuum decreases to approximately 1 psi vacuum (approx. 2"Hg).
Normal operating vacuum for the system is between 2"Hg and 6"Hg.
System does not restrict the vacuum source to 85±15 liters/hour flow rate at the "Alarm On" vacuum level.
Volume of monitored interstitial space must not exceed 8 m3 (2114 gal) for tanks and 10 m3 (2642 gal) for piping.
When monitoring double-walled tanks, the system does not require a liquid stop valve, a condensate trap or liquid sensors. Since the vacuum line is connected to the pump siphon port, any liquid in the vacuum line will be returned to the tank. Suction line must be located at lowest point of interstitial space.
Calibration Functional and operational safety tests should be performed in accordance with manufacturer's instructions.
Initial calibration with known leak is performed at system installation, using an orifice supplied by the manufacturer.

Interstitial space is tested continuously.
Vacuum source is the submerged turbine pump siphon port.
Presence of a water table above the leak point will allow water to enter the interstice rather than air or vapor. The water would be detected in the same manner as fuel.
This system may not be compatible with all secondarily contained tanks and/or piping. Always consult with the tank and/or piping manufacturer and the manufacturer's applicable recommended installation practices before installing this system, or damage may be caused to the tank or piping by its use.


Franklin Fueling Systems           

Evaluator:  Ken Wilcox Associates

3760 Marsh Road         

Tel:  (816) 443-2494

Madison, WI 53718

Date of Evaluation:  11/11/04

Tel:  (800) 225-9787  
E-mail: info@franklinfueling.com  

URL: www.franklinfueling.com


 | Home | Vendors: A - F | Vendors: G - M | Vendors: N - S | Vendors: T - Z | Method Index |

Appearance on this list is not to be construed as an endorsement by any regulatory agency nor is it any guarantee of the performance of the method or equipment.
Equipment should be installed and operated in accordance with all applicable laws and regulations.
For full details, please refer to our expanded "DISCLAIMER" page.